Manuale Hotpoint GA2 124 IX HA Forno

Manuale

CLEANING AND MAINTENANCE

Make sure that the oven has cooled down before carrying out any maintenance or cleaning.

Do not use steam cleaners.

Do not use wire wool, abrasive scourers or abrasive/corrosive cleaning agents, as these could damage the surfaces of the appliance.

Wear protective gloves.

The oven must be disconnected from the mains before carrying out any kind of maintenance work.

EXTERIOR SURFACES

Clean surfaces with a damp microbre cloth. If they are very dirty,

add a few drops of pH-neutral detergent. Finish o with a dry cloth.

Do not use corrosive or abrasive detergents. If any of these products

inadvertently comes into contact with the surfaces of the appliance,

clean immediately with a damp microbre cloth.

INTERIOR SURFACES

After every use, leave the oven to cool and then clean it, preferably

while it is still warm, to remove any deposits or stains caused by

food residues. To dry any condensation that has formed as a result

of cooking foods with a high water content, leave the oven to cool

completely and then wipe it with a cloth or sponge.

Clean the glass in the door with a suitable liquid detergent.

The oven door can be removed to facilitate cleaning.

ACCESSORIES

Soak the accessories in a washing-up liquid solution after use, handling

them with oven gloves if they are still hot. Food residues can be

removed using a washing-up brush or a sponge.

CLEANING THE CATALYTIC PANELS

(ONLY IN SOME MODELS)

This oven could be equipped with special catalytic liners that facilitate

cleaning of the cooking compartment thanks to their special self-

cleaning coating, which is highly porous and able to absorb grease and

grime. These panels are tted to the shelf guides: When repositioning

and then retting the shelf guides, make sure that the hooks at the top

are slotted into the appropriate holes in the panels.

1

2

To make best use of the catalytic panels’ self-cleaning properties, we

recommend heating the oven to 200 °C for around one hour using the

“Convection Bake” function. The oven must be empty during this time.

Then leave the oven to cool down before removing any remaining food

residues using a non-abrasive sponge.

Please note: Using corrosive or abrasive cleaning agents, stiff brushes,

pan scourers or oven sprays could damage the catalytic surface and

compromise its self-cleaning properties. Please contact our After-sales

Service if you require replacement panels.

REPLACING THE LAMP

Disconnect the oven from the power supply, unscrew the cover from

the light, replace the bulb and screw the cover back on the light.

Reconnect the oven to the power supply.

Please note: Only use 20-40 W/230 V type G9, T300 °C halogen bulbs. The

bulb used in the product is specifically designed for domestic appliances

and is not suitable for general room lighting within the home (EC

Regulation 244/2009). Light bulbs are available from our After-sales Service.

If using halogen bulbs, do not handle them with your bare hands as your

fingerprints could cause damage. Do not use the oven until the light cover

has been refitted.

REMOVING AND REFITTING THE DOOR

To remove the door, open it fully and lower the catches until they are in

the unlock position (1). Close the door as much as you can (2).

Take a rm hold of the door with both hands – do not hold it by the

handle. Simply remove the door (3) by continuing to close it while

pulling it upwards (a) at the same time until it is released from its

seating (b).

1

2

~60°

3

a

b

~15°

Put the door to one side, resting it on a soft surface.

Ret the door by moving it towards the oven, aligning the hooks of the

hinges with their seating and securing the upper part onto its seating.

Lower the door and then open it fully. Lower the catches into their

original position: make sure that you lower them down completely.

Try closing the door and check to make sure that it lines up with the

control panel. If it does not, repeat the steps above.

CLICK & CLEAN - CLEANING THE GLASS

After removing the door and resting it on a soft surface with the

handle downwards, simultaneously press the two retaining clips (1) and

remove the upper edge of the door by pulling it towards you (2).

1

2

Lift and rmly hold the inner glass with both hands, remove it and

place it on a soft surface before cleaning it (3).

3

To correctly reposition the inner glass, make sure that the “R” is visible

in the left-hand corner and the clear surface (not printed) is facing up.

First insert the long side of the glass indicated by “R” into the support

seats, then lower it into position (4). Ret the upper edge (5): a click will

indicate correct positioning. Make sure the seal is secure before

retting the door.

4

5

Valutazione

Maggiori informazioni su questo manuale

Comprendiamo che sia bello avere un manuale cartaceo per i tuoi Hotpoint GA2 124 IX HA Forno. Puoi sempre scaricare il manuale dal nostro sito web e stamparlo tu stesso. Se desideri avere un manuale originale, ti consigliamo di contattare Hotpoint. Potrebbero essere in grado di fornire un manuale originale. Stai cercando il manuale del tuo Hotpoint GA2 124 IX HA Forno in un'altra lingua? Scegli la tua lingua preferita sulla nostra home page e cerca il numero del modello per vedere se è disponibile.

Specifiche

Tutti i manuali per Hotpoint Forni
Altri manuali di Forni

Domande frequenti su Hotpoint GA2 124 IX HA Forno

Il nostro team di supporto cerca informazioni utili sul prodotto e risposte alle domande più frequenti. Se trovi un’inesattezza nelle nostre domande frequenti, ti preghiamo di farcelo sapere utilizzando il nostro modulo di contatto.

Prodotti correlati

Manuale

Hotpoint FI7 891 SP IX HA Forno

Manuale

Hotpoint FID 834 H MR HA Forno

Manuale

Hotpoint FI9 891 SH IX HA Forno

Manuale

Hotpoint FA3 530 H BL HA Forno

Manuale

Hotpoint FI5 851 C IX HA Forno

Manuale

Hotpoint FI6 871 SC IX HA Forno

Manuale

Hotpoint HAOI78PHT1SBA Forno

Manuale

Hotpoint FIT 804 H AV HA Forno

Categorie correlate