Manuale Makita DJV182ZJ Seghetto alternativo

Manuale

9

Press the lock switch to turn the tool into standby mode. It

turns the lamp on, too.

Pull the switch trigger to start the tool. Release the switch

trigger to stop.

For continuous operation, pull the switch trigger and then

push in the lock on button.

To stop the tool from the locked position, pull the switch

trigger fully, and then release it.

In standby mode, press the lock switch to turn the lamp off

and turn the tool into lock-off mode.

NOTE:

• The lock switch does not actuate during cutting

operation.

• When the tool is in standby mode, the lamp keeps

lighting.

• If the tool is left 10 seconds without any operations in

standby mode, the tool is automatically turned into

lock-off mode and the lamp goes off.

Lighting up the lamps

CAUTION:

• Do not look in the lamp or see the source of lamp

directly.

To turn on the lamp, press the lock switch.

To turn off the lamp within 10 seconds, press the lock

switch again.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

• When the tool is overheated, the lamp flickers. Cool

down the tool fully before operating again.

Speed adjusting dial (Fig. 6)

The tool speed can be infinitely adjusted by turning the

speed adjusting dial. You can get the highest speed at 6

and the lowest speed at 1.

Refer to the table to select the proper speed for the

workpiece to be cut. However, the appropriate speed may

differ with the type or thickness of the workpiece. In

general, higher speeds will allow you to cut workpieces

faster but the service life of the blade will be reduced.

013925

CAUTION:

• The speed adjusting dial can be turned only as far as 6

and back to 1. Do not force it past 6 or 1, or the speed

adjusting function may no longer work.

Electronic function

The tool is equipped with the electronic functions for easy

operation.

• Soft start

The soft-start function minimizes start-up shock, and

makes the tool start smoothly.

• Soft no-load rotation

To reduce the vibration and align the jig saw blade with

the cutting line easily, the tool automatically reduces

the rotation speed until the tool starts cutting the

workpiece when the speed adjusting dial is set at 3 or

higher. Once the tool starts cutting the workpiece, the

tool speed reaches the preset speed and keeps the

speed until the tool stops.

NOTE:

• When the temperature is low, this function may not be

available.

Disabling the soft no-load rotation

function

Country specific

To disable the soft no-load rotation function, follow the

steps below.

1. Make sure that the tool is turned off.

2. Set the speed adjusting dial to “1”.

3. Press the lock/unlock button to turn on the tool.

4. Set the speed adjusting dial to “6” by turning it, and

then set it to “1” by turn it back.

The lamp blinks twice to indicate that the soft no-load

rotation function is disabled. To enable this function again,

perform the same procedure again.

NOTE:

• If the soft no-load rotation function is disabled, the lamp

blinks twice when the tool is turned on.

• You can also disable or enable the soft no-load rotation

function by changing the speed adjusting dial from “6”

to “1” and changing it from “1” to “6”.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing saw blade

CAUTION:

• Always clean out all chips or foreign matter adhering to

the blade and/or blade holder. Failure to do so may

cause insufficient tightening of the blade, resulting in a

serious personal injury.

• Do not touch the blade or the workpiece immediately

after operation; they may be extremely hot and could

burn your skin.

• Tighten the saw blade securely. Failure to do so may

cause a serious injury.

• When you remove the saw blade, be careful not to hurt

your fingers with the top of the blade or the tips of

workpiece. (Fig. 7)

Before installing the blade, make sure that the blade

holder is in the released position.

To install the blade, insert the blade (teeth facing forward)

into the blade holder until it latches. The blade holder

moves to the fixed position by itself and the blade is

Workpiece to be cut Number on adjusting dial

Wood 4 - 6

Mild steel 3 - 6

Stainless steel 3 - 4

Aluminum 3 - 6

Plastics 1 - 4

Valutazione

Maggiori informazioni su questo manuale

Comprendiamo che sia bello avere un manuale cartaceo per i tuoi Makita DJV182ZJ Seghetto alternativo. Puoi sempre scaricare il manuale dal nostro sito web e stamparlo tu stesso. Se desideri avere un manuale originale, ti consigliamo di contattare Makita. Potrebbero essere in grado di fornire un manuale originale. Stai cercando il manuale del tuo Makita DJV182ZJ Seghetto alternativo in un'altra lingua? Scegli la tua lingua preferita sulla nostra home page e cerca il numero del modello per vedere se è disponibile.

Specifiche

Tutti i manuali per Makita Seghe alternative
Altri manuali di Seghe alternative

Domande frequenti su Makita DJV182ZJ Seghetto alternativo

Il nostro team di supporto cerca informazioni utili sul prodotto e risposte alle domande più frequenti. Se trovi un’inesattezza nelle nostre domande frequenti, ti preghiamo di farcelo sapere utilizzando il nostro modulo di contatto.

Prodotti correlati

Manuale

Makita 4351FCT Seghetto alternativo

Manuale

Makita 4329J Seghetto alternativo

Manuale

Makita DJV182 Seghetto alternativo

Manuale

Makita 4351FCTK Seghetto alternativo

Manuale

Makita 4351T Seghetto alternativo

Manuale

Makita 4350FCT Seghetto alternativo

Manuale

Makita 4350T Seghetto alternativo

Manuale

Makita 4341T Seghetto alternativo

Categorie correlate