Manuale Denver TRC-1460 Stazione meteorologica

Manuale

~P.2~

and hold 2 seconds to clear both IN/OUT temperature memory.

D. [+] & [-] button

Press the [-] side to decrease the setting when enter setting mode of clock, alarm or temperature alert.

When display the alarm time, press [-] side to turn Daily Alarm on/off.

When display the temperature alert, press [-] side to turn the corresponding temperature alert on/off.

Press the [+] side to increase the setting when enter setting mode of clock, alarm or temperature alert.

E. [CHANNEL] button

Toggle to display remote thermo channel from channel 1, channel 2, channel 3 to Auto-scroll mode which alternately

display 3 channels;

Press and hold 2 seconds to activate searching mode for remote sensor;

Remote Sensor

The remote sensor has 3 function buttons inside the battery compartment.

a. [CH] button

After the battery installation, the LED blinks slowly every 1.5 seconds and channel number shows ‘1’ to indicate it is now

under channel setting mode and is set to channel 1 by default. If the user presses no key within ten seconds, the unit

will auto-exit the channel setting.

If the user press [CH] button once during the channel setting, the channel number is changed to ‘2’ to indicate the unit

is set to channel 2. If the user press [CH] button again, the channel number will be advanced to channel ‘3’ and so on.

b. [C/F] button (for sensor with LCD)

Press to toggle unit °C or °F

c. [RESET] button

Press to hardware reset the unit to factory setting

3.

BATTERY INSTALLATION

BATTERY INSTALLATION FOR MAIN UNIT

a. Remove the battery door;

b. Insert 2 pieces AAA size 1.5V alkaline battery as indicate by the polarity;

c. Close the battery door.

BATTERY INSTALLATION FOR REMOTE SENSOR UNIT

a. Lift off the bracket stand of the remote sensor unit by releasing the 2 fixing snaps at the bottom;

b. Use a small Philips type screwdriver to remove the battery cover screws;

c. Insert 2 pieces of AAA size batteries according to the “+” and “-” polarity marks shown in the battery compartment and

then close the battery door.

WIRELESS REMOTE SENSOR REGISTRATION PROCEDURE

a. Insert x2 AAA batteries first to the main unit. The temperature display shows ‘—.-C‘ while the wave icon will keep

blinking for 2 minutes indicate the main unit is in sensor searching mode.

b. In a second step, insert the x2 AAA batteries into the sensor unit. The LED on the front panel will start flashing at a rate

of one time per around 2 seconds indicates channel-1 is in use.

c. While the LED is flashing, press once the [CH] key will change the sensor channel setting to 2. Keep toggle on [CH] key

can change channel setting up to 3. The LED is blinking at a frequency to indicate the channel setting. i.e. continuous

blinks 2 times indicate channel-2 is selected.

4.

HOW TO SET TIME AND CALENDAR

a. Make sure the 1

st

line of the LCD displays the clock time, press & hold [CLOCK] button for 2 seconds to enter clock setting

mode. Flashing 24 hours will appear.

b. Press [ + ] or [ - ] button to switch between 24 hours and 12 hours format, and then press [CLOCK] button to confirm.

c. The hour digits will flash. Use the [ + ] button to increase by one hour or [ - ] button to decrease by one hour to your

desired hours. Holding down either button will change the increment rapidly. Press [CLOCK] button to confirm.

d. The minute digits will flash. Use the [ + ] button or [ - ] button to set your desired minutes. Holding down either button

will change the increment rapidly. Press [CLOCK] button to confirm.

e. The year digit will flash and Yr icon appears. Press [ + ] or [ - ] button to set your desired year. Press [CLOCK] button to confirm.

f. D and M icons will flash. Press [ + ] or [ - ] to select D M (Date Month) or M D (Month Date) format. Press [CLOCK]

button to confirm.

Note: Never set the channel to ‘4’ & ‘5’ which would not be applied in this model

NOTE: Please insert batteries for the main unit first, then the RF remote sensor.

Note: If user does not press any key for 10 seconds, it will exit the channel setting mode and transmit the RF signal.

The main unit will register the temperature reading.

Note: Every change of minute digit will automatically reset the seconds to zero.

Note: Year range is from 2000 to 2099.

ENG

Valutazione

Maggiori informazioni su questo manuale

Comprendiamo che sia bello avere un manuale cartaceo per i tuoi Denver TRC-1460 Stazione meteorologica. Puoi sempre scaricare il manuale dal nostro sito web e stamparlo tu stesso. Se desideri avere un manuale originale, ti consigliamo di contattare Denver. Potrebbero essere in grado di fornire un manuale originale. Stai cercando il manuale del tuo Denver TRC-1460 Stazione meteorologica in un'altra lingua? Scegli la tua lingua preferita sulla nostra home page e cerca il numero del modello per vedere se è disponibile.

Specifiche

Tutti i manuali per Denver Stazioni meteorologica
Altri manuali di Stazioni meteorologica

Domande frequenti su Denver TRC-1460 Stazione meteorologica

Il nostro team di supporto cerca informazioni utili sul prodotto e risposte alle domande più frequenti. Se trovi un’inesattezza nelle nostre domande frequenti, ti preghiamo di farcelo sapere utilizzando il nostro modulo di contatto.

Prodotti correlati

Manuale

Denver TRC-1470 Stazione meteorologica

Manuale

Denver WS-72 Stazione meteorologica

Manuale

Denver TRC-1480 Stazione meteorologica

Manuale

Denver TRC-1400 Stazione meteorologica

Manuale

Auriol IAN 345566 Stazione meteorologica

Manuale

Oregon BAR 623P Stazione meteorologica

Manuale

Bresser 9604200 Meteo Temp Stazione meteorologica

Manuale

Auriol IAN 300120 Stazione meteorologica

Categorie correlate