5
Lock
• While still holding the switch handle,
tighten the locking ring clockwise, using
the other hand. Only light finger pressure
is required to secure it (Fig. 3.3).
How to adjust the height of your
trimmer (Fig. 3)
Your trimmer has a telescopic body, thus
allowing you to alter its height to give you the
most comfortable operating position.
3
To adjust the height of your trimmer:
Unlock
• With the trimmer switched off and the
edge guide (9) resting on the ground,
place one hand on the switch handle
(20). Using your other hand, turn the
locking ring (4) anti-clockwise,
approximately quarter of a turn (Fig. 3.1).
Adjust
• While keeping hold of the switch handle,
grasp the trimmer body (1) with your other
hand and raise/lower the switch handle
to your desired operating position (Fig. 3.4).
Lock
• While still holding the switch handle,
tighten the locking ring clockwise, using
the other hand. Only light finger pressure
is required to secure it (Fig. 3.3).
How to alter the position of the
secondary handle (Fig. L)
Your trimmer has an adjustable secondary
handle to allow you to position it for maximum
comfort and balance. It can be folded flat for
compact storage.
L
To adjust the handle:
• With the trimmer guard resting on the
ground, depress the button (27) with
your hand.
• While keeping the button depressed,
lift/lower the secondary handle to the
desired position with your other hand.
• Releasing the button will automatically
lock the handle in one of the preset
positions.
How to alter the cutting head angle
of your trimmer (Fig. M & N)
Your trimmer has a variable cutting head angle.
• To give you the optimum trimming angle
independent of your personal height
(Fig. C).
M
• To raise the handle to a more comfortable
height when in the edging mode. Tip:
Alter the cutting head angle by lowering
the handle one or two knotches, while in
the trimming mode, prior to converting to
the edging mode (Fig. M).
N
• To gain access under benches, garden
furniture and shrubs (Fig. N).
To alter the cutting head angle:
• With the guard (6) resting on the ground,
depress the pedal (26) with your foot.
• Raise/lower the switch handle (20) while
keeping the pedal depressed. The
cutting head will automatically lock when
you remove your foot from the pedal.
Replacement line
A new spool containing 10 metres of cutting line
(cat. no. A6481) may be purchased from your
Black & Decker dealer. Alternatively, replacement
line packs are available containing either 25m
(cat. no. A6170), 40m (cat. no. A6171) or 50m
(cat. no. A6054) of line.
For maximum reliability, never put on a heavier or
lighter line (e.g. fishing line) which will prevent the
automatic feed from functioning, cause motor failure
or reduce cutting performance.
How to fit a new spool of cutting line
(Fig. 4 & 5)
• Disconnect your trimmer from the
power supply.
4
• Remove the spool cover by pushing the
spool cover tabs (13) inwards and
upwards (Fig. 4), then pull off (it is not
necessary to push both tabs in at the
same time). The empty spool can now
be withdrawn from the drive shaft.
• Remove any dirt or grass that may have
collected inside the spool housing (12)
and cover (8).
5
• Unwind approximately 9cm (3.5") of cutting
line (5) from the new spool (17). Feed the
cutting line through the eyelet and then
push the spool onto the centre drive shaft
(Fig. 5). Rotate as necessary to fully seat
the spool, taking care not to trap the cutting
line underneath the spool and making
sure that there is a minimum of 9cm
(3.5") protruding from the spool housing.
ENGLISH
Partecipa alla conversazione su questo prodotto
Qui puoi condividere cosa pensi di Black and Decker GL580 Tagliabordi. Se hai una domanda, leggi prima attentamente il manuale. La richiesta di un manuale può essere effettuata utilizzando il nostro modulo di contatto.
rispondi | È stato utile (0) (Tradotto da Google)
rispondi | È stato utile (0) (Tradotto da Google)