Manuale Stickfast SL120 Pistola incollatrice

Manuale

EDITION FEB 2017

Warning

When using this hot melt glue gun always follow basic safety

p

recautions. Wear protective gloves, long sleeved clothing and

safety glasses, to reduce the possibility of accidental injury.

Read all the safety instructions.

Read all the safety instructions

Safety instructions

X

tegra

®

S

tickfast™ 240v model glue guns are recommended for

i

ndoor use only and should not be used in wet or damp conditions.

Your work area should be well lit. The operating temperature of

the guns is between 120˚C- 230˚C. Do not touch the heated nozzle

or molten adhesive with bare skin. Protective gloves should al-

ways be worn. Careless handling can cause skin burns.

If molten adhesive comes into contact with the skin, immerse the

a

ected area immediately in cold water. Seek medical advice if

necessary, do not remove the adhesive from the skin.

Disconnect the electrical power supply to the glue gun after use,

before servicing and when changing accessories.

Allow time for the gun nozzle to cool down suciently before

handling. Never immerse the gun or its nozzle in water or other

liquids to accelerate the cooling process. Do not leave the gun

unattended while plugged in or still hot. If it is not to be reused

within one hour, disconnect the electrical power supply.

It is normal for this device to become warm during use and does

not indicate a problem.

Operation (All glue guns except SL150B)

> Use only recommended Stickfast™ adhesives in this glue

gun. The use of other manufacturers’ products will

invalidate the warranty.

> Before using the gun for the first time check carefully for

signs of external damage. If any damage has occurred in

transit do not use it; return it to your supplier immediately.

> Attach the enclosed metal glue gun stand, locating the

hooks on its legs in the holes on either side of the gun

casing.

> Insert a Stickfast™ glue stick into the rear of the tool and

push the stick forward until slight resistance is felt.

> Plug the gun into a 240V AC outlet and allow the tool to

heat up for approximately 3-5 minutes. When the gun is

fully heated squeeze the trigger until the molten adhesive

begins to flow from the nozzle.

> Release the trigger to stop the flow. Do not apply

excessive pressure to the trigger as this can cause

blockages. If a blockage occurs, leave the gun to stand for

a minute, then gently try again.

> The first time a glue gun is used it may smoke from the

nozzle. This is normal and will stop as soon as glue has

filled the melt chamber.

> Apply the adhesive wherever it is required. When adhesive

can no longer be extruded from the tool, insert a new glue

stick into the rear of the tool to resume operation.

Operation (SL150B cordless model)

> Use only recommended Stickfast™ adhesives in this glue

g

un. The use of other manufacturers’ products will

invalidate the warranty.

> Before using the gun for the first time check carefully for

s

igns of external damage. If any damage has occurred in

t

ransit do not use it; return it to your supplier immediately.

> Turn on to heat the gun; a red light is illuminated to

indicate power supply.

>

Insert a Stickfast™ glue stick into the rear of the tool and

push the stick forward until slight resistance is felt.

> Pre-heat time is about 5-8 minutes before the gun is

ready to use. When the gun is fully heated squeeze the

trigger until the molten adhesive begins to flow from

t

he nozzle.

> Release the trigger to stop the flow. Do not apply

excessive pressure to the trigger as this can cause

blockages. If a blockage occurs, leave the gun to stand

for a minute, then gently try again.

> The first time a glue gun is used it may smoke from the

nozzle. This is normal and will stop as soon as glue has

filled the melt chamber.

> Apply the adhesive wherever it is required. When

adhesive can no longer be extruded from the tool, insert

a new glue stick into the rear of the tool to resume

operation.

> The indicator light flashes for two minutes before the

battery is exhausted and the heater turns o

automatically. Replace with a fully charged battery to

resume operation.

> Operating time is about 60 minutes (based on our

suggested battery capacity, 1.3Ah 36V)

> To release the battery, press the battery lock button. To

replace the battery, push battery in to the base of the gun

until the battery locks in place.

> Warning: Please take extra care with the heated nozzle;

the SL150B is a cordless model and it is easy to forget

that the gun may still be hot.

4

STICKFAST Operating Instructions

G

B

Valutazione

Maggiori informazioni su questo manuale

Comprendiamo che sia bello avere un manuale cartaceo per i tuoi Stickfast SL120 Pistola incollatrice. Puoi sempre scaricare il manuale dal nostro sito web e stamparlo tu stesso. Se desideri avere un manuale originale, ti consigliamo di contattare Stickfast. Potrebbero essere in grado di fornire un manuale originale. Stai cercando il manuale del tuo Stickfast SL120 Pistola incollatrice in un'altra lingua? Scegli la tua lingua preferita sulla nostra home page e cerca il numero del modello per vedere se è disponibile.

Specifiche

Tutti i manuali per Stickfast Pistole incollatrice
Altri manuali di Pistole incollatrice

Domande frequenti su Stickfast SL120 Pistola incollatrice

Il nostro team di supporto cerca informazioni utili sul prodotto e risposte alle domande più frequenti. Se trovi un’inesattezza nelle nostre domande frequenti, ti preghiamo di farcelo sapere utilizzando il nostro modulo di contatto.

Prodotti correlati

Manuale

Stickfast GX80LT Pistola incollatrice

Manuale

Stickfast GX600 Pistola incollatrice

Manuale

Stickfast SL150B Pistola incollatrice

Manuale

Stickfast GX600A Pistola incollatrice

Manuale

Stickfast GX120 Pistola incollatrice

Manuale

Stickfast GX300 Pistola incollatrice

Manuale

Stickfast GX80 Pistola incollatrice

Manuale

Stickfast SL300 Pistola incollatrice

Categorie correlate