Manuale Sammic GCP-350 Affettatrice

Manuale

3

ENGLISH

MODELS

This manual describes the installation,

operation and maintenance of the GC-220,

GC-250, GC-275, GC-300, GCP-250, GCP-

275, GCP-300 and GCP-350 Slicers.

The model reference and its specifications

are shown on the identification plate loca-

ted in the machine.

These slicer machines have been designed

and manufactured in accordance with the

following European directive: 89/392/EEC.

INSTALATION

For a suitable working operation and long

service life of the machine, follow the ins-

tructions contained in this manual.

Positioning

Place the slicer on a flat and firm area.

Small off-levels can be compensated by

means of the adjustable feet.

ELECTRIC INSTALATION

The slicers are single phase and are sup-

plied for 220V.

Before connecting the Slicer to the mains,

check if the motor is prepared for the same

voltage as the mains.

They must be EARTHED.

STARTING

1.Check if the Slicing control knob (A) is in

position "0".

2.Lay the goods on the Carriage (B), retai-

ning them with the Carriage handle set

(C).

3.Turn the Slicing control knob (A) till you

get the desired thickness.

4.Switch on the Start/stop switch (D) in

order to make the Blade (E) run and make

sure it rotates anti-clockwise.

Always use the Carriage handle set (C)

when you cut, never use your hands to

hold the goods during the cutting opera-

tion. Grasp the Pusher lever (F) to push

the Carriage (B).

5.When you have finished cutting, stop the

slicer by switching off the Start/stop

switch (D) and replace the Slicing control

knob (A) into position "0".

MAINTENANCE

Before cleaning, overhauling or repairing

the machine, it is necessary to unplug it

from the mains.

Sharpening de blade

This operation is essential to obtain a per-

fect cut and ensure a long service life of the

blade.

Sharpening the blade must be carried out

when the blade is clean only. Sharpening a

dirty blade would cause damage to both

blade and the grinding wheel, in addition

to poor results.

After sharpening the blade, brush the grin-

ding wheel to eliminate any food residues.

Besides, clean blade and grinding wheel

with an alcohol-impregnated cloth to remo-

ve all traces of grinding dust.

For correct sharpening, proceed as descri-

bed below:

1.Degrease both sides of the blade (E) with

an alcohol-impregnated cloth.

2.Pull on the sharpener set (H), loosening

Sharpener holder (G); turn it clockwise

180º. Fix the Sharpener set (H) tightening

Sharpener holder (G).

3.Switch on the machine and press the

Grinding abrasive pushbutton (I) to start

the grinding abrasive (J).

4.Press the Grindstone pushbutton (K) to

have the Grindstone (L) remove the burrs

that formed on the front edge of the

blade during sharpening.

IMPORTANT: Sharpening should last

about 20 seconds. Deburring should not

last more than 2 or 3 seconds.

5.Switch off the Start/stop switch (D) and

let down the Sharpener set (H) to its ori-

ginal storage position.

Cleaning

For hygiene reasons, the slicer must be

kept clean. It is therefore necessary to strip

down the machine and clean it at the end

of the workday as well as when changing

the sort of food to be cut.

1.Disconnect the slicer from the mains.

Simply switching off the Start/stop

switch (D) is not sufficient.

2.Place the Slicing control knob (A) in posi-

tion "0".

3.Clean the entire surface with a soft cloth

and hot and soapy water. Do not use

abrasives or dry detergents because they

would harm the anodized surface.

4.To clean the Blade (E), remove the Blade

guard (M) by unscrewing the Rosette tie

(N). Clean with an alcohol-impregnated

cloth.

5.To clean the Carriage set (B), unscrew

Carriage knob (O).

6.Lubricate all the slicing parts with non-

vegetable oil.

WARNING

1.Absolutely do not remove the security

Transparent guard (P).

2.Do not slice up material which is not

foodstuff.

3.If you want your machine to work pro-

perly, periodically check if the blade, the

sharpening stones and the drive belt are

in good conditions.

OTHER IMPORTANT REMARKS

-In the event the power supply cable should

get damaged and have to be replaced, the

repair may only be done by a SAMMIC

approved assistance service.

-The level of noise emission for a machine

working loaded, placed 1,6 metre high and

measured at a distance of 1 metre is less

than 70 dB (A). Backgrond noise: 32 dB (A).

Valutazione

Maggiori informazioni su questo manuale

Comprendiamo che sia bello avere un manuale cartaceo per i tuoi Sammic GCP-350 Affettatrice. Puoi sempre scaricare il manuale dal nostro sito web e stamparlo tu stesso. Se desideri avere un manuale originale, ti consigliamo di contattare Sammic. Potrebbero essere in grado di fornire un manuale originale. Stai cercando il manuale del tuo Sammic GCP-350 Affettatrice in un'altra lingua? Scegli la tua lingua preferita sulla nostra home page e cerca il numero del modello per vedere se è disponibile.

Specifiche

Tutti i manuali per Sammic Affettatrici
Altri manuali di Affettatrici

Prodotti correlati

Manuale

Sammic GCP-275 Affettatrice

Manuale

Sammic GC-275 Affettatrice

Manuale

Sammic GCP-300 Affettatrice

Manuale

Sammic GCP-250 Affettatrice

Manuale

Sammic GC-300 Affettatrice

Manuale

Sammic GC-250 Affettatrice

Manuale

Sammic GC-220 Affettatrice

Manuale

Kooper 2192037 Affettatrice

Categorie correlate