Manuale Parkside IAN 280254 Fresatrice per scanalature

Manuale

PMNF 1350 B2

■ 18 

│

 GB

│

MT

Further safety instructions for

abrasive cutting applications

Kickback and corresponding safety instructions

Kickback - causes and corresponding safety

instructions

▯ Kickback is a sudden reaction caused when a

rotating grinding disc catches or jams. Catching

or jamming causes the rotating accessory tool

to stop abruptly. If this happens, an uncontrolled

power tool turns rapidly against the direction

of rotation of the accessory tool caught in the

blockage.

▯ If, for example, a grinding disc catches or jams,

the edge of the grinding disc that is projecting

into the workpiece can get caught and break

off the grinding disc or cause a kickback. The

grinding disc can then fly in the direction of the

operator or away from him, depending on the

direction of rotation of the disc at the blockage.

This can also break grinding discs.

A kickback is caused by incorrect use or misuse

of the power tool. This can be avoided by taking

proper precautions as given below.

a) Hold the power tool firmly in both hands and

position your arms so they can absorb the

force of a kickback. Always use the additional

handle, if available, so you have the maximum

control over the kickback force or reaction

torques at full speed. By taking adequate pre-

cautions, the operator can stay in control of the

kickback and reaction torques.

b) Never hold your hand close to a rotating

accessory tool. The accessory tool could hit

your hand in the case of a kickback.

c) Avoid the area in front of and behind the rotat-

ing cutting disc. The kickback will force the power

tool in the opposite direction to the direction of

rotation of the grinding disc at the blockage.

d) Take special care when working around

corners, sharp edges, etc. Avoid allowing

the accessory tool to bounce back from the

workpiece or jam. The rotating accessory tool

is more likely to jam in corners or sharp edges

or if it bounces. This can cause a loss of control

or kickback.

e) Do not use a toothed or chain saw blade or

segmented diamond-coated disc with more

than 10 mm wide slits. Such accessory tools

cause a kickback or loss of control over the

power tool.

f) Avoid cutting disc jams or excessive contact

pressure. Do not make any excessively deep

cuts. Overloading the cutting disc increases the

stress and likelihood of tilting or jamming and

thus the possibility of kickback or breakage of

the grinding tool.

g) If the cutting disc jams or you stop working,

switch the tool off and hold it steady until the

disc has completely stopped turning. Never

attempt to pull a rotating cutting disc out of a

cut. This could lead to kickback. Identify and

remove the cause of the jam.

h) Do not switch the power tool back on as long

as it is in the workpiece. Allow the cutting disc

to reach its full speed before you carefully

continue the cut. Otherwise, the disc may jam,

jump out of the workpiece or cause kickback.

i) Support panels or large workpieces to reduce

the risk of the cutting disc jamming and causing

a kickback. Large workpieces can bend under

their own weight. The workpiece must be sup-

ported on both sides, namely in the vicinity of

the cut and also at the edge.

j) Be particularly careful when making "pocket

cuts" into existing walls or other obscured

areas. The inserted cutting disc may cut into

gas or water pipes, electrical wiring or other

objects that can cause kickback.

Valutazione

Maggiori informazioni su questo manuale

Comprendiamo che sia bello avere un manuale cartaceo per i tuoi Parkside IAN 280254 Fresatrice per scanalature. Puoi sempre scaricare il manuale dal nostro sito web e stamparlo tu stesso. Se desideri avere un manuale originale, ti consigliamo di contattare Parkside. Potrebbero essere in grado di fornire un manuale originale. Stai cercando il manuale del tuo Parkside IAN 280254 Fresatrice per scanalature in un'altra lingua? Scegli la tua lingua preferita sulla nostra home page e cerca il numero del modello per vedere se è disponibile.

Specifiche

Tutti i manuali per Parkside Fresatrici per scanalature
Altri manuali di Fresatrici per scanalature

Domande frequenti su Parkside IAN 280254 Fresatrice per scanalature

Il nostro team di supporto cerca informazioni utili sul prodotto e risposte alle domande più frequenti. Se trovi un’inesattezza nelle nostre domande frequenti, ti preghiamo di farcelo sapere utilizzando il nostro modulo di contatto.

Prodotti correlati

Manuale

Parkside PMNF 1350 E4 Fresatrice per scanalature

Manuale

Parkside IAN 303235 Fresatrice per scanalature

Manuale

Parkside IAN 317149 Fresatrice per scanalature

Manuale

Parkside IAN 93548 Fresatrice per scanalature

Manuale

Einhell TE-MA 1500 Fresatrice per scanalature

Manuale

FERM WSM1009 Fresatrice per scanalature

Manuale

FERM WSM1008 Fresatrice per scanalature

Manuale

Vonroc WC502AC Fresatrice per scanalature

Categorie correlate