Manuale Makita HR2630T Martello perforatore

Manuale

9

Grasp the change cover of the quick change drill chuck

and turn the change cover line to the symbol until a

click can clearly be heard.

Selecting action mode

CAUTION:

• Do not rotate the action mode changing knob when the

tool is running. The tool will be damaged.

• To avoid rapid wear on the mode change mechanism,

be sure that the action mode changing knob is always

positively located in one of the three action mode

positions.

Rotation with hammering (Fig. 8)

For drilling in concrete, masonry, etc., rotate the action

mode changing knob to the symbol. Use a tungsten-

carbide tipped bit.

Rotation only (Fig. 9)

For drilling in wood, metal or plastic materials, rotate the

action mode changing knob to the

m symbol. Use a twist

drill bit or wood bit.

Hammering only (Fig. 10)

For chipping, scaling or demolition operations, rotate the

action mode changing knob to the

g symbol. Use a bull

point, cold chisel, scaling chisel, etc.

Torque limiter

CAUTION:

• As soon as the torque limiter actuates, switch off the

tool immediately. This will help prevent premature wear

of the tool.

• Bits such as hole saw, which tend to pinch or catch

easily in the hole, are not appropriate for this tool. This

is because they will cause the torque limiter to actuate

too frequently.

The torque limiter will actuate when a certain torque level

is reached. The motor will disengage from the output

shaft. When this happens, the bit will stop turning.

Hook (Fig. 11)

For Model HR2641

CAUTION:

• Never hook the tool at high location or on potentially

unstable surface.

The hook is convenient for hanging the tool temporarily.

To use the hook, simply lift up hook until it snaps into the

open position.

When not in use, always lower hook until it snaps into the

closed position.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Side grip (auxiliary handle) (Fig. 12)

CAUTION:

• Always use the side grip to ensure operating safety.

Install the side grip so that the protrusions on the grip fit

in between the grooves on the tool barrel. Then tighten

the grip by turning clockwise at the desired position. It

may be swung 360° so as to be secured at any position.

Bit grease

Coat the bit shank head beforehand with a small amount

of bit grease (about 0.5 – 1 g).

This chuck lubrication assures smooth action and longer

service life.

Installing or removing the bit

Clean the bit shank and apply bit grease before installing

the bit. (Fig. 13)

Insert the bit into the tool. Turn the bit and push it in until

it engages. (Fig. 14)

After installing, always make sure that the bit is securely

held in place by trying to pull it out.

To remove the bit, pull the chuck cover down all the way

and pull the bit out. (Fig. 15)

Bit angle (when chipping, scaling or demolishing)

The bit can be secured at the desired angle. To change

the bit angle, rotate the action mode changing knob to

the O symbol. Turn the bit to the desired angle. (Fig. 16)

Rotate the action mode changing knob to the

g symbol.

(Fig. 17)

Then make sure that the bit is securely held in place by

turning it slightly.

Depth gauge

The depth gauge is convenient for drilling holes of

uniform depth. (Fig. 18)

Press the lock button on the grip base in the direction of

arrow shown in the figure and with the lock button being

pressed insert the depth gauge into the hex. hole in the

grip base. (Fig. 19)

At this time, the depth gauge needs to be inserted so that

its toothed side is directed to the toothed side of hex hole

marking on the grip base as shown in the figure. (Fig. 20)

Adjust the depth gauge to the desired depth by moving it

back and forth while pressing the lock button. After the

adjustment, release the lock button to lock the depth

gauge. (Fig. 21)

NOTE:

• Inserting the depth gauge with its toothed side not

directed to the toothed side of hex hole marking on the

grip base as shown in the figure does not allow the

depth gauge to be locked.

Dust cup (optional accessory) (Fig. 22)

Use the dust cup to prevent dust from falling over the tool

and on yourself when performing overhead drilling

operations. Attach the dust cup to the bit as shown in the

figure. The size of bits which the dust cup can be

attached to is as follows.

006406

There is another type of dust cup (optional accessory)

which helps you prevent dust from falling over the tool

and on yourself when performing overhead drilling

operations.

Bit diameter

Dust cup 5 6 mm – 14.5 mm

Dust cup 9 12 mm – 16 mm

Valutazione

Maggiori informazioni su questo manuale

Comprendiamo che sia bello avere un manuale cartaceo per i tuoi Makita HR2630T Martello perforatore. Puoi sempre scaricare il manuale dal nostro sito web e stamparlo tu stesso. Se desideri avere un manuale originale, ti consigliamo di contattare Makita. Potrebbero essere in grado di fornire un manuale originale. Stai cercando il manuale del tuo Makita HR2630T Martello perforatore in un'altra lingua? Scegli la tua lingua preferita sulla nostra home page e cerca il numero del modello per vedere se è disponibile.

Specifiche

Tutti i manuali per Makita Martelli perforatori
Altri manuali di Martelli perforatori

Domande frequenti su Makita HR2630T Martello perforatore

Il nostro team di supporto cerca informazioni utili sul prodotto e risposte alle domande più frequenti. Se trovi un’inesattezza nelle nostre domande frequenti, ti preghiamo di farcelo sapere utilizzando il nostro modulo di contatto.

Prodotti correlati

Manuale

Makita DHR202 Martello perforatore

Manuale

Makita HR2420 Martello perforatore

Manuale

Makita BHR262 Martello perforatore

Manuale

Makita HR3210C Martello perforatore

Manuale

Makita HR3012FC Martello perforatore

Manuale

Makita 8035NBI Martello perforatore

Manuale

Makita BHR202 Martello perforatore

Manuale

Makita HR166D Martello perforatore

Categorie correlate