Manuale Makita HR2460 Martello perforatore

Manuale

5

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and

unplugged before adjusting or checking function on the

tool.

Switch action (Fig. 1)

CAUTION:

• Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

“OFF” position when released.

To start the tool, simply pull the switch trigger. Tool speed

is increased by increasing pressure on the switch trigger.

Release the switch trigger to stop. For continuous opera-

tion, pull the switch trigger and then push in the lock but-

ton. To stop the tool from the locked position, pull the

switch trigger fully, then release it.

Lighting up the lamps (Fig. 2)

For Model HR2460F

CAUTION:

• Do not look in the light or see the source of light

directly.

To turn on the lamp, pull the trigger. Release the trigger

to turn it off.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

Reversing switch action (Fig. 3)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• If the switch trigger can not be depressed, check to see

that the reversing switch is fully set to position (A

side) or (B side).

This tool has a reversing switch to change the direction

of rotation. Move the reversing switch lever to the

position (A side) for clockwise rotation or to the posi-

tion (B side) for counterclockwise rotation.

Selecting the action mode (Fig. 4)

This tool employs an action mode changing knob. Select

one of the two modes suitable for your work needs by

using this knob.

For rotation only, turn the knob so that the arrow on the

knob points toward the symbol on the tool body.

For rotation with hammering, turn the knob so that the

arrow on the knob points toward the symbol on the

tool body.

CAUTION:

• Always set the knob fully to your desired mode symbol.

If you operate the tool with the knob positioned half-

way between the mode symbols, the tool may be dam-

aged.

• Use the knob after the tool comes to a complete stop.

Torque limiter

The torque limiter will actuate when a certain torque level

is reached. The motor will disengage from the output

shaft. When this happens, the bit will stop turning.

CAUTION:

• As soon as the torque limiter actuates, switch off the

tool immediately. This will help prevent premature wear

of the tool.

• Bits such as hole saw, which tend to pinch or catch

easily in the hole, are not appropriate for this tool. This

is because they will cause the torque limiter to actuate

too frequently.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and

unplugged before carrying out any work on the tool.

Side grip (auxiliary handle) (Fig. 5)

CAUTION:

• Always use the side grip to ensure operating safety.

Install the side grip so that the teeth on the grip fit in

between the protrusions on the tool barrel. Then tighten

the grip by turning clockwise at the desired position. It

may be swung 360° so as to be secured at any position.

Bit grease

Coat the bit shank head beforehand with a small amount

of bit grease (about 0.5 – 1 g).

This chuck lubrication assures smooth action and longer

service life.

Installing or removing the bit

Clean the bit shank and apply bit grease before installing

the bit. (Fig. 6)

Insert the bit into the tool. Turn the bit and push it in until

it engages. (Fig. 7)

After installing, always make sure that the bit is securely

held in place by trying to pull it out.

To remove the bit, pull the chuck cover down all the way

and pull the bit out. (Fig. 8)

Depth gauge (Fig. 9)

The depth gauge is convenient for drilling holes of uni-

form depth. Loosen the side grip and insert the depth

gauge into the hole in the side grip. Adjust the depth

gauge to the desired depth and tighten the side grip.

NOTE:

• The depth gauge cannot be used at the position where

the depth gauge strikes against the gear housing.

Dust cup (Fig. 10)

Use the dust cup to prevent dust from falling over the tool

and on yourself when performing overhead drilling oper-

ations. Attach the dust cup to the bit as shown in Fig. 10.

The size of bits which the dust cup can be attached to is

as follows.

Bit diameter

Dust cup 5 6 mm – 14.5 mm

Dust cup 9 12 mm – 16 mm

Valutazione

Maggiori informazioni su questo manuale

Comprendiamo che sia bello avere un manuale cartaceo per i tuoi Makita HR2460 Martello perforatore. Puoi sempre scaricare il manuale dal nostro sito web e stamparlo tu stesso. Se desideri avere un manuale originale, ti consigliamo di contattare Makita. Potrebbero essere in grado di fornire un manuale originale. Stai cercando il manuale del tuo Makita HR2460 Martello perforatore in un'altra lingua? Scegli la tua lingua preferita sulla nostra home page e cerca il numero del modello per vedere se è disponibile.

Specifiche

Tutti i manuali per Makita Martelli perforatori
Altri manuali di Martelli perforatori

Domande frequenti su Makita HR2460 Martello perforatore

Il nostro team di supporto cerca informazioni utili sul prodotto e risposte alle domande più frequenti. Se trovi un’inesattezza nelle nostre domande frequenti, ti preghiamo di farcelo sapere utilizzando il nostro modulo di contatto.

Prodotti correlati

Manuale

Makita HR3550C Martello perforatore

Manuale

Makita HR2631F Martello perforatore

Manuale

Makita DHR164 Martello perforatore

Manuale

Makita HR2811F Martello perforatore

Manuale

Makita HR5000 Martello perforatore

Manuale

Makita HR2430 Martello perforatore

Manuale

Makita BHR262T Martello perforatore

Manuale

Makita HR2811FT Martello perforatore

Categorie correlate