Manuale Makita DUN600LZ Tagliasiepi

Manuale

15 ENGLISH

Reverse button for debris removal

WARNING: If the entangled branches or

debris cannot be removed by the reverse func-

tion, switch off the tool and remove the bat-

tery cartridge, and then remove the entangled

branches or debris using tools such as pliers.

Failuretoswitchoffthetoolandremovethebat-

terycartridgemayresultinseriouspersonalinjury

fromaccidentalstart-up.Removingtheentangled

branchesordebrisbyhandmaycauseaninjury,

sincetheshearbladesmaymoveinreactionto

removing them.

Thistoolhasareversebuttontochangethedirection

ofshearbladesmovement.Itisonlyforremoving

branchesanddebrisentangledinthetool.

Toreversetheshearbladesmovement,pressthereverse

button when the shear blades have stopped, and then pull the

switchtriggerwhilepressingthelever.Thepowerlampstarts

blinking,andtheshearbladesmoveinreversedirection.

Whenentangledbranchesanddebrisareremoved,

the tool returns to the regular movement and the power

lamp stops blinking and lights up.

►Fig.7: 1.Powerlamp2. Reverse button

NOTE:Iftheentangledbranchesordebriscannotbe

removed,releasetheswitchtrigger,thenpressthe

reversebutton,andthenpulltheswitchtriggeruntil

theyareremoved.

NOTE:Ifyoutapthereversebuttonwhiletheshear

bladesarestillmoving,thetoolcomestostopandto

bereadyforreversemovement.

Adjusting the cutting angle

CAUTION: Always be sure that the tool is

switched off before folding or unfolding the head.

CAUTION: When folding the head for carrying

the tool or after using the tool, be sure to attach

the blade cover before folding the head.

CAUTION: When folding the head, be careful

not to pinch your ngers between the head and

the slide sleeve.

For DUN500W

Theangleoftheheadcanbeadjustedin6steps.To

changetheangleofthehead,followthestepsbelow.

1.

Holdtheheadandtheslidesleeveasshowninthegure.

►Fig.8: 1. Head 2. Slide sleeve

2. Move the head while holding down the slide

sleeve, and then release the slide sleeve.

3. Movetheheadslightlyuntilitislockedwithaclick.

NOTE:Makesurethattheheadissecurelylocked

beforeoperatingthetool.

Hex wrench storage

For DUN600L

Whennotinuse,storethehexwrenchasillustratedto

keepitfrombeinglost.

►Fig.9: 1. Handle 2.Hexwrench

ASSEMBLY

CAUTION: Always be sure that the tool is

switched off and the battery cartridge is removed

before carrying out any work on the tool.

CAUTION: When replacing the shear blades,

always wear gloves so that your hands do not

directly contact the blades.

Installing the handle

For DUN600L

1. Attachtheupperandlowerclampsonthedamper.

2. Putthehandleontheupperclampandxitwith

bolts as illustrated.

►Fig.10: 1. Bolt 2. Handle 3.Upperclamp4. Damper

5.Lowerclamp

Installing or removing the shear blades

CAUTION: Attach the blade cover before

removing or installing the shear blades.

NOTICE: When replacing the shear blades, do

not wipe off grease from the gear and crank.

NOTICE:

For DUN500W

Do not install 600 mm shear blades to your tool.

If600mmshearbladesareinstalledtothetool,you

cannotfoldtheheadofthetool.

NOTE:

For DUN500W

Beforeinstallingorremovingtheshearblades,unfold

theheadofthetoolsothattheheadisstraighttothe

toolbody.

1. Placethetoolupsidedown,andthenremove6

bolts.

►Fig.11: 1. Bolt

2. Removethecover,gasket,plateA,andplateB.

►Fig.12: 1. Cover 2. Gasket 3.PlateA4.PlateB

NOTE:Thegasketorplatesmayremainonthecover.

3. Remove the rod and the bearing.

►Fig.13: 1. Rod 2. Bearing

NOTE:Therodorbearingmayremainonthecover.

4. Remove2bolts,2sleeves,andthefeltpad,and

then remove the shear blades.

►Fig.14: 1.Feltpad2. Bolt 3. Sleeve 4. Shear blades

NOTICE: Be careful not to lose the bolts.

5. Removethebladecover,andthenattachittothe

new shear blades.

►Fig.15

6. Adjustthecranksothat2holesarelinedupon

the alignment line.

►Fig.16: 1. Hole 2.Alignmentline

Valutazione

Maggiori informazioni su questo manuale

Comprendiamo che sia bello avere un manuale cartaceo per i tuoi Makita DUN600LZ Tagliasiepi. Puoi sempre scaricare il manuale dal nostro sito web e stamparlo tu stesso. Se desideri avere un manuale originale, ti consigliamo di contattare Makita. Potrebbero essere in grado di fornire un manuale originale. Stai cercando il manuale del tuo Makita DUN600LZ Tagliasiepi in un'altra lingua? Scegli la tua lingua preferita sulla nostra home page e cerca il numero del modello per vedere se è disponibile.

Specifiche

Tutti i manuali per Makita Tagliasiepi
Altri manuali di Tagliasiepi

Domande frequenti su Makita DUN600LZ Tagliasiepi

Il nostro team di supporto cerca informazioni utili sul prodotto e risposte alle domande più frequenti. Se trovi un’inesattezza nelle nostre domande frequenti, ti preghiamo di farcelo sapere utilizzando il nostro modulo di contatto.

Prodotti correlati

Manuale

Makita DUH501Z Tagliasiepi

Manuale

Makita DUN461WSYE Tagliasiepi

Manuale

Makita UH006GM201 Tagliasiepi

Manuale

Makita 550MM Tagliasiepi

Manuale

Makita DUH601Z Tagliasiepi

Manuale

Makita UH4570 Tagliasiepi

Manuale

Makita UH6570 Tagliasiepi

Manuale

Makita UH650D Tagliasiepi

Categorie correlate