Manuale Makita 6797D Avvitatore

Manuale

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if

it is severely damaged or is completely worn

out. The battery cartridge can explode in a fire.

8. Be careful not to drop, shake or strike battery.

9. Do not charge inside a box or container of any

kind. The battery must be placed in a well

ventilated area during charging.

ADDITIONAL SAFETY RULES

FOR TOOL

ENB026-1

1. Be aware that this tool is always in an operat-

ing condition, because it does not have to be

plugged into an electrical outlet.

2. Hold tool by insulated gripping surfaces when

performing an operation where the cutting tool

may contact hidden wiring. Contact with a

‘‘live’’wire will also make exposed metal parts

of the tool ‘‘live’’ and shock the operator.

3. Always be sure you have a firm footing.

Be sure no one is below when using the tool in

high locations.

4. Hold the tool firmly.

5. Keep hands away from rotating parts.

SAVE THESE INSTRUCTIONS.

OPERATING INSTRUCTIONS

Installing or removing battery cartridge

(Fig. 1)

•

Always switch off the tool before insertion or

removal of the battery cartridge.

•

To remove the battery cartridge, pull out the set

plate on the tool and grasp both sides of the

cartridge while withdrawing it from the tool.

•

To insert the battery cartridge, align the tongue on

the battery cartridge with the groove in the housing

and slip it into place. Snap the set plate back into

place. Be sure to close the set plate fully before

using the tool.

•

Do not use force when inserting the battery car-

tridge. If the cartridge does not slide in easily, it is

not being inserted correctly.

Charging

Before using battery charger, read all instructions and

cautionary markings on the battery charger.

Tips for maintaining maximum battery life

1. Always stop tool operation and charge the battery

cartridge when you notice that the warning lamp

lightened up.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F).

Let a hot battery cartridge cool down before

charging it.

Installing or removing bit (Fig. 2)

CAUTION:

Always be sure that the tool is switched off and the

battery cartridge is removed before installing or

removing the bit.

Use only the driver bit or socket bit shown in the figure

below.

Do not use any other driver bit or socket bit.

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will

go. Then release the sleeve to secure the bit.

To remove the bit, pull the sleeve in the direction of

the arrow and pull the bit out firmly.

Adjusting the fastening torque (Fig. 3)

Use an optional adjust grip to adjust the fastening

torque.

Insert the pins of the adjust grip into the holes in the

front of the tool. And then, turn the adjust grip so that

the torque gauge shows the desired torque by one of

the numbers from 1 to 12.

The number provides fastening torque in newton-

meter (N

.

m), and see below for the standard fastening

torque;

6796D/FD: 1 – 5 (Nzm)

6797D/FD: 2 – 8 (Nzm)

6798D/FD: 6 – 12 (Nzm)

After completion of the adjustment, always make trial

fastening about twenty times in order to keep stability

of torque. Then, check the fastening torque with a

torque tester before starting operation.

Switch action (Fig. 4)

CAUTION:

Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the ‘‘OFF’’ position when

released.

To start the tool, simply pull the trigger. Release the

trigger to stop.

Lighting up front lamps (Fig. 5)

(for 6796FD/6797FD/6798FD only)

Pull the trigger to light up the front lamps. And the

lamps keep on lighting while the trigger is being

pulled. The light automatically goes out 10 to 20

seconds after the trigger is released.

5

Valutazione

Maggiori informazioni su questo manuale

Comprendiamo che sia bello avere un manuale cartaceo per i tuoi Makita 6797D Avvitatore. Puoi sempre scaricare il manuale dal nostro sito web e stamparlo tu stesso. Se desideri avere un manuale originale, ti consigliamo di contattare Makita. Potrebbero essere in grado di fornire un manuale originale. Stai cercando il manuale del tuo Makita 6797D Avvitatore in un'altra lingua? Scegli la tua lingua preferita sulla nostra home page e cerca il numero del modello per vedere se è disponibile.

Specifiche

Tutti i manuali per Makita Avvitatori
Altri manuali di Avvitatori

Domande frequenti su Makita 6797D Avvitatore

Il nostro team di supporto cerca informazioni utili sul prodotto e risposte alle domande più frequenti. Se trovi un’inesattezza nelle nostre domande frequenti, ti preghiamo di farcelo sapere utilizzando il nostro modulo di contatto.

Prodotti correlati

Manuale

Makita BFS440 Avvitatore

Manuale

Makita 6833 Avvitatore

Manuale

Makita BFT125F Avvitatore

Manuale

Makita DFT124R Avvitatore

Manuale

Makita 6820V Avvitatore

Manuale

Makita BFT041F Avvitatore

Manuale

Makita 6798D Avvitatore

Manuale

Makita FS2700 Avvitatore

Categorie correlate