ENGLISH
1
IMPORTANT
1. This booklet is an integral and essential part of the product
and should be kept and preserved by the user. Please read
carefully the guidelines and warnings contained herein as
they are intended to provide the installer/user with essential
information for the proper installation and the continued safe
use and maintenance of the product. Please preserve this
booklet for any further consultation that may be necessary.
2. This is a commercial icemaker, and should be destined only
to be used for the purpose for which it has been expressly
designed. Any other use should be considered improper
and therefore dangerous. The manufacturer will not be held
liable or responsible for any damage caused by improper,
incorrect and unreasonable use.
I. INSTALLATION INSTRUCTIONS
WARNING
The installation must be carried out by qualied personnel,
in accordance with current regulations, according to the
manufacturer’s instructions.
1. UNPACKING
WARNING
Children should not be allowed in reach of the packaging
elements (plastic bags and expanded polystyrene) as they are
potential sources of danger.
CAUTION
Remove shipping carton, tape(s) and packing. If packing
material is left in the icemaker, it will not work properly.
1) After removing the packaging, make sure that the icemaker is in
good condition. If in doubt, please do not use the equipment but
apply to professionally qualied personnel.
2) Remove shipping tape holding the Door and Separator.
3) Remove the protective plastic lm from the exterior. If the icemaker
is exposed to the sun or to heat, remove the lm after the icemaker
cools.
4) Remove the package of accessories, and check the contents:
a) Outlet Hose 1
b) Scoop 1
c) Hose Adapter 1
d) Duct 1
e) Screw 3
f) Leg 4
5) Attach the Duct to the Rear Panel using the three screws provided.
See Fig. 1.
2. LOCATION
IMPORTANT
1. This icemaker is not intended for outdoor use. Normal
operating ambient temperature should be within 7°C to 43°
C. Normal operating water temperature should be within 7°
C to 35°C. Operation of the icemaker, for extended periods,
outside of these normal temperature ranges may affect
production capacity.
2. The icemaker should not be located next to ovens, grills or
other high heat producing equipment.
3. The location should provide a rm and level foundation for
the equipment.
4. Allow at least 5 cm clearance at the right side for proper air
circulation and at least 15 mm clearance at top for ease of
maintenance and/or service should they be required.
5. This appliance is not suitable for installation in an area where
a water jet could be used and where dripping is not allowed.
6. Do not place anything on top, front and right side of the
icemaker. Especially, do not block the air inlet at the right
side.
7. This icemaker will not work at subfreezing temperatures. To
prevent damage to the water supply line, drain the icemaker
when air temperature is below zero (see “II. 2. PREPARING
THE ICEMAKER FOR LONG STORAGE”).
3. INSTALLATION
* Incorrect installation can cause harm to people, animals or things,
for which the manufacturer cannot be held responsible.
* Place the icemaker in the selected permanent site.
* The appliance must be positioned so that the plug is accessible.
4. ELECTRICAL CONNECTIONS
WARNING
THIS APPLIANCE MUST BE EARTHED
This icemaker requires an earth that meets the national
and local electrical code requirements. To prevent possible
severe electrical shock to individuals or extensive damage to
equipment, install a proper earth wire to the icemaker. Remove
the plug from the mains socket before any maintenance, repairs
or cleaning is undertaken.
* This icemaker must have a separate power supply or receptacle of
220 - 240V.
Fig. 1
Door
Louver
Magnet Catch
Air Filter
Separator
(inside)
Air Inlet
(Air Filter)
Duct
Screw
Rear View
How to remove Louver
Partecipa alla conversazione su questo prodotto
Qui puoi condividere cosa pensi di Hoshizaki KM-100A Macchina per cubetti di ghiaccio. Se hai una domanda, leggi prima attentamente il manuale. La richiesta di un manuale può essere effettuata utilizzando il nostro modulo di contatto.