Manuale FERM TDM1011 Trapano a colonna da banco

Manuale

50 Ferm

SPARE PARTS LIST

POSITION DESCRIPTION NO.

28 SPRING-TERSION 311106

29 CAP-SPRING 311107

38 MOTOR 311103

59 V-BELT 311104

2 RACK 311108

64 SWITCH 311105

79 KEY-DRIFT 311109

10 ARBOR 311110

11 CHUCK 311111

TABLE DRILLING MACHINE

THE NUMBERS IN THE FOLLOWING TEXT COR-

RESPOND WITH THE PICTURES AT PAGE 2

TECHNICAL SPECIFICATIONS

PRODUCT INFORMATION

Fig.A

1. On/off switch

2. Drill dept gauge

3. Protection guard

4. Motor

5. Drill dept lever

6. Table adjustment

Check first whether or not the delivery has been dama-

ged by transport and/or whether all the parts are pre-

sent.

SAFETY INSTRUCTIONS

The following pictograms are used in these instructions

for use:

Denotes risk of personal injury, loss of life or

damage to the tool in case of non-observance of

the instructions in this manual.

Denotes risk of electric shock.

Faulty and/or discarded electrical or electronic

apparatus have to be collected at the appropriate

recycling locations.

Carefully read this manual before using the machine.

Make sure that you know how the machine functions and

how to operate it. Maintain the machine in accordance

with the instructions to make sure it functions properly.

Keep this manual and the enclosed documentation with

the machine.

When using electric machines always observe the

safety regulations applicable in your country to

reduce the risk of fire, electric shock and personal

injury. Read the following safety instructions and

also the enclosed safety instructions.

Keep these instructions in a safe place!

Before using the machine the guidelines must be taken

into consideration. Every mechanical or electrical altera-

tion to the machine which does not meet the applicable

guidelines carries a considerable accident risk.

During use the following points must be taken

into consideration:

• Do not remove any mechanical or electrical protec-

tive provisions.

• Check whether all the protective provisions are in

place and have been attached correctly.

• Wear safety goggles during drilling.

• If you have long hair, be sure to wear hair protection

(hair net or cap). Long hair can easily be caught in

moving parts.

• Wear fitted clothing; tie buttons on sleeves.

• Do not hold any workpieces in your hands when dril-

ling. Always use a machine clamp or another clam-

ping tool.

• Protect workpieces and clamping tools on the bench

to prevent them from getting caught. Fasten them

yourself with screws or clamp them to a machine

clamp fastened to the table.

• Check whether the drill holder is tightened properly.

• Check whether cable lead-throughs are okay.

• To remove drill chips only use hand brushes, brus-

hes, rubber wipers, chip hooks or similar aids.

• Do not carry out any cleaning or greasing work while

the machine is in operation.

• Always keep V-belts covered (so that your hands

cannot become caught).

• Only tighten the toothed ring drill holder by means

of the wrench.

• Never leave the wrench of the drill holder in the drill

holder! Before switching on the machine, check

whether the wrench really has been removed!

• Do not use any drills which are damaged on the

shank.

• The drill is not suitable for moulding!

• If the mains cable is damaged, it may only be replaced

by a mains cable of the same type.

IMMEDIATELY SWITCH OFF THE MACHINE

WHEN:

• Interruption in the mains plug, mains lead or mains

lead damage.

• Defect switch.

• Smoke or stench of scorched isolation.

ELECTRICAL INSTALLATION

The machine is provided with an electrical installation,

which meets the standards. Repairs may only be carried

Voltage | 400 V~

Frequency | 50 Hz

Power input | 1100 W

No load speed | 96-1988/min

Number of speeds | 9 (L/R)

Chuck capacity/Morse Conisch | 16 mm/MT4

Weight | 135 kg

Lpa (sound pressure level) | 88 dB(A)

Lwa (sound power level) | 101 dB(A)

Vibration value | <2,5 m/s

2

Ferm 3

Valutazione

Maggiori informazioni su questo manuale

Comprendiamo che sia bello avere un manuale cartaceo per i tuoi FERM TDM1011 Trapano a colonna da banco. Puoi sempre scaricare il manuale dal nostro sito web e stamparlo tu stesso. Se desideri avere un manuale originale, ti consigliamo di contattare FERM. Potrebbero essere in grado di fornire un manuale originale. Stai cercando il manuale del tuo FERM TDM1011 Trapano a colonna da banco in un'altra lingua? Scegli la tua lingua preferita sulla nostra home page e cerca il numero del modello per vedere se è disponibile.

Specifiche

Tutti i manuali per FERM Trapani a colonna da banco
Altri manuali di Trapani a colonna da banco

Domande frequenti su FERM TDM1011 Trapano a colonna da banco

Il nostro team di supporto cerca informazioni utili sul prodotto e risposte alle domande più frequenti. Se trovi un’inesattezza nelle nostre domande frequenti, ti preghiamo di farcelo sapere utilizzando il nostro modulo di contatto.

Prodotti correlati

Manuale

FERM TDM1012 Trapano a colonna da banco

Manuale

FERM TDM1006 Trapano a colonna da banco

Manuale

FERM TDM1005 Trapano a colonna da banco

Manuale

FERM TDM1008 Trapano a colonna da banco

Manuale

FERM TDM1020 Trapano a colonna da banco

Manuale

FERM TDM1007 Trapano a colonna da banco

Manuale

FERM TDM1003 Trapano a colonna da banco

Manuale

FERM TDM1027 Trapano a colonna da banco

Categorie correlate